PENINGKATAN SIFAT MEKANIK DAN TERMAL KAYU KELAPA SAWIT DENGAN TEKNIK KOMPREGNASI REAKTIF

Authors

  • Nurfajriani .
  • Wesly Hutabarat
  • Thamrin .
  • Basuki Wirjosentono
  • Saharman Gea

Keywords:

Oil Palm Trunks, mechanical properties, compregnation reactive, resin

Abstract

Characterization of Oil Palm Trunks (OPT) in height roddifferent OPT that compregnated with polystyrene resin modificationshave been done, polystyrene resins modified with acrylic acid and benzoyl peroxide incorporated into the OPT pore size 15x2x2 cm3 shaped beam that is placed in the compregnator has been modified with -5 atm pressure for 15 minutes. Based on the tensile tests conducted showed that the optimum mechanical properties of the OPT on the bottom of the stem height. with the addition of 20% resin. Similarly, the thermal properties OPT marked increases with increasing temperature degradation of OPT compregnated modified polystyrene resin at a concentration of 20%. From the above two tests showed that OPT improved quality of prior treatment compregnation, analysis of thermal degradation by using Thermogravimetry

References

Abidin Y, (2009) Tesis Master, Pressure

and temperature influence on the

compregnation

process

on

mechanical properties of oil palm

trunk, Teknik Pertanian, Unand.

Departemen Pertanian, statistik

Pertanian, 2010

Hashim, R., Said, N., Lamaming, J.,

Baskaran.,Sulaiman, O., Sato, M.,

Hiziroglu, S and Sugimoto, T. 2011.

Influence of Press Temperature On

The Properties of Binderless Particle

Board Made From Oil Palm Trunk.

Journal Of Material and Design. 32:

Hoong, Y.B and Paridah, M.T. 2013.

Development a New Method for

Pilot Scale Production of High Grade Oil Palm Plywood: Effect of HotPressing

Time. Journal Material and

Design. 45: 145

H™ng, P.S., Chai, L.Y., Tay, P.W., Wong,

S.Y., Wong, W.Z., Chow, M.J., and

Chai, E.W. 2013. Urea Formaldehyde

Impregnated Oil Palm Trunk as Core

Layer for Three Layer Board. Journal

of Material and Design.50: 457

Loh, Y.F., Paridah, M.T., Hoong, Y.B.,

Yoong, A.C.C. 2011. Effect of

Treatment With Low Molecular

Weight Phenol Formaldehyde Resin

On the Surface Characteristics of Oil

Palm (Elaeisquineensis) Stem Veneer.

Journal Material and Design.32: 2277.

Nurfajriani, Hafni, (2011) Pemanfaatan

Limbah KKS dengan Teknik

Impregnasi, Laporan akhir Research

Grant Unimed, Medan

Yaolin Zhang,1,2 S. Y. Zhang,1,2 Ying Hei

Chui,2 Hui Wan,1 Mosto Bousmina3

(2006) Wood Plastic Composites by Melt

Impregnation: Polymer

Retention and Hardness. Journal of

Applied polymer Sience, Vol. 102,

-1680.

Zaini, M.J, M Y A Fuad, M S Mansor, dan

J Mustafah, (1996) The effect of Filler

Content and Size on The Mechanical

Properties of Polypropilene Oil Palm

Wood Flour Composite. Polymer

International, 40 (1), 51-55.

Zaini, M.J, M Y A Fuad, M S Mansor, dan

J Mustafah, (1996) Application of Oil

Palm Wood Flour as Filler in

Polypropylene, Polymer Journal, 26 (5),

-642.

Zoja Bednarek1, Agnieszka KaliszukWietecka.

(2007) Analysis of The

Fire-Protection

Impregnation

Influence On Wood Strength. Journal

of Civil Engineering and

Management. Vol. XIII. No 2. 79-85.

Downloads

Published

2019-01-31

Issue

Section

VOL 14, NO 2 (2014): JURNAL PENELITIAN SAINTIKA